简要说明：Kjellberg牌的Kjellberg电极产品：估价：111，规格：完善，产品系列编号：齐全

　　Kjellberg电极
Upgrade to Centricut performance
consumables to lower your operating
costs without sacrificing cut quality
and productivity.
Lower overall costs
? Centricut consumables last more than 15% longer than
Kjellberg mild steel consumables.
? Full line of consumables for all cutting applications are
competitively priced compared to the OEM.
? Local stocking and fast delivery reduce your inventory costs.
Hypertherm patented technology
? As the recognized global leader in plasma cutting, Hypertherm
incorporates the latest engineered technologies into all
consumable products.
? SilverLine? electrodes and CoolFlow? nozzles deliver
exceptional cut quality and fast cutting speeds over the full life
of the consumables.
? Centricut consumables set the standard by which other
manufacturers measure themselves.
Cut with confidence – it’s Hypertherm
? Designed with critical-to-function tolerances to deliver the best
quality product every time.
? Precision manufacturing of consumables assures consistency
of parts set to set.
? World-class plasma-process technical support.
? Easy to use – no special system set up required.
To achieve maximum consumable life
A fully used SilverLine? electrode will have a
pit depth of 2.5 mm (.100").
Properly tighten the nozzle cap: Make
sure the nozzle cap is sealed tightly against
the nozzle to maintain a proper seal and
prevent leaking.
Purge torch and leak check: After each
parts change purge the torch for at least
30 seconds to remove residual moisture.
Check for leaks.
Adjust gas flows: Plasma gas flow rate is
critical. High flow will cause rapid electrode
wear and hard starting. Low flow will cause
uncontrolled arcing. (See cutting tables in
your owner’s manual.)
Pierce at correct height: Piercing too low
causes molten metal (spatter) to hit the swirl
gas cap and nozzle. This is the most common
cause of premature nozzle failure. Piercing
Reference
number
Article
number Descrtption
Centricut
number
1. K2-XL .11.828.921.300 SilverLine electrode C53-1000
K2 .12.40870 Electrode C53-870
2. K5 .11.828.911.550 Electrode ArH2 C117-0550
3. .12.40860 Gas guide cap C53-860
4. L1-XL .11.828.901.420 CoolFlow nozzle, O2, 160A C53-920
L2-XL .11.828.901.425 CoolFlow nozzle, O2, 250A C53-925
L4-XL .11.828.901.427 CoolFlow nozzle, O2, 300A C53-927
L1 .12.4305 Nozzle, Air, 160A, 2.0 mm C53-050
L2 .12.40850 Nozzle, Air, 250A, 2.5 mm C53-850
5. A1 .12.37780 CoolFlow nozzle, ArH2, 120A, 1.5 mm C117-780
A3 .11.828.511.620 CoolFlow nozzle, ArH2, 180A, 2.0 mm C117-620
A2 .12.40910 CoolFlow nozzle, ArH2, 300A, 2.3 mm C117-910
6. V3000 .12.37790 Nozzle cap C53-790
7. V521 .11.833.101.271 Swirl gas nozzle K53-271
8. V501 .11.833.101.261 Protective cap C53-261
.11.828.701.160 Protective cap PB-S75 K53-160
9. V4540 .11.833.111.156 Swirl gas cap, 4.0 mm K53-1156
V4550 .11.833.101.158 Swirl gas cap, 5.0 mm C53-158
.11.828.911.230 Cooling tube PB-S75 ArH2 C117-230
.12.51440 Cooling tube PB-S75 Air K53-440
too high can cause slow arc transfer and
misfires.
Adjust arc voltage: As the electrode wears,
the torch will get closer to the plate. To maintain
optimum cutting height, increase arc voltage in
2-volt increments, up to 10 volts higher than
the initial setting.
Avoid arc stretching: This can occur during
rip cutting off the plate or when the lead out
is improperly programmed. This shortens
consumable life.
Clean the nozzle and swirl gas cap:
Periodically clean the nozzle and swirl gas cap
to remove spatter. This will prevent double
arcing which shortens consumable life.
Adjust swirl gas flows: Correct swirl gas
flows during pre-flow protect the nozzle and
swirl gas cap from damage. Make sure pre-flow
is adjusted according to the cutting tables in
your owner’s manual.