| 详细介绍： 厦门晶鼎自动化科技有限公司现货供应CS10-R电流开关，欢迎前来咨询，谢谢！联系人：黄明航 ，电话：05925586900/13599928764 传真：0592-5328257 QQ:70666131
1. 应用
CL10-W作为传统电缆室照明灯的替代方案，采用
LED作为发光光源，并采取特殊的结构，实现低成本、
高可靠、易用性的应用设计。
1. Application
The CL10-W is the substitute of the traditional cable
cabinet lamp, adopt LED as light source, and adopt
special structure, carry out low cost and high reliability
and use easily .
□ The power supply adapt to AC/DC110V~230V, The
electric circuit adopt to import IC, and the convert
efficiency is high, the heat is small, the life is long.
□ Adopt the Phoenix spring connector.
□ The control unit install in instrument cabinet, easy to
make maintenance.
□ The luminescent head is fixed in place needed light
of cable cabinet with screw conveniently and fast.
□ Little volume's luminescent head make the cable
cabinet clean and neat.
□ Choose the LED that suitable with the cable cabi-
net
illuminance, ensure illuminance effect with lower
power consumption
□ Since LED life is long, replacing is not be acted as
normal situation.
□ Connecting cable linked with illuminance head
adopts a quickly link part, easy to install and re-
place.
□ With reliable protective structure, the luminescent
head ’s mar is reduced.
□ The house adopt flame retardant material.
□ 适应电源范围宽，AC/DC110V~230V，控制电路
采用进口IC，转换效率高，发热量小，寿命长。
□ 接线端子采用Phoenix弹簧接线端子。
□ LED光源控制单元安装于开关柜仪表室，便于更
换。
□ 发光头可用螺栓夹紧的方式安装在电缆室需要光
照的地方，方便快捷。
□ 体积小巧的发光端可使电缆室布局整洁美观。
□ 选用电缆室照明场合适用的LED，既降低了功耗
又保证了照明效果。
□ 在高压柜的使用寿命期内，基于LED光源的长寿
特性，正常使用情况下不用更换LED，免除了电
缆室更换光源的风险。
□ 连接电缆与发光头连接采用快速连接器，便
于安装更换。
□ 发光头采用可靠的防护结构，可有效减少不当安
装及使用可能对LED造成的损伤。
□ 外壳采用阻燃材料。
3. 型号说明
CL10-W
10是设计序列号；
W是光源颜色白色“white”的简写。
4. 技术参数
□ 电源：AC/DC110V~230V
□ 功耗：<4W
□ 连接电缆：阻燃电缆2×0.5mm2
，3.5米
（电缆长度可依用户需求提供）
□ LED：采用高亮LED，寿命不少于50000小时
□ 耐压强度：AC2500V，1Min
□ 工作环境温度：-25ºC~50ºC
□ 相对温度：25%~95%（40℃）
□ 发亮时间：1800s±15% （也可按客户要求设定）
□ 再次启动间隔时间：不超过8秒钟
提示：延迟时间到后，须断开电源！等待不超过8秒，再
次送电时，灯就能重新亮起，并重算延迟时间。
4. Technique parameters
□ Rated power voltage: AC/DC110V~230V
□ Power Consumption: <4W
□ Connecting cable: Flame retardant cable, 3.5m
(length is variable for demand of customer)
□ LED: Use highlight LED, the life span is no less
than for 50000 hours
□ Insulating strength:AC2500V,1Min
□ Ambient temperature:：-25ºC~50ºC
□ Relative humidity:25%~95%（40℃）
□ Lighting continuance: 1800s±15% (variable for
demand of customer)
□ Re-start interval: Less than 8 seconds.
Prompt:After delay time arrived, must disconnect power
supply! Waiting for no less than 8seconds, connect
Power supply again, the light would re-start, and
calculate a delay time over again.
CL10-W
The “10” is Design serial number;
The “W” is a brief of “White” , it is color of light
source.
3. Models explanation
2. 特点及优点 2. Features and advantages
5. 使用方法
将光源控制单元安装于便于安全操作区域，发光
头安装于需要照明区域的合适位置。接通电源，光源
控制单元通过连接电缆点亮发光头，照亮选定区域。
接通电源后，因发光持续时间的出厂标准设定为30分
钟，30分钟后自动熄灭。若要重新启动，必须在断开
电源不少于8秒后再接通电源。
建议:在每次使用后断开电源。
5. Use method
The light source control unit mount in the easy to safety
operation region, illuminance head mounts in the suita-
ble place that the end illuminates a region in the de-
mand. Connect a power supply, illuminance head take
power from the light source control unit, illuminating a
region selected. After connecting a power supply, the
plant standard keeping on time setting that gives out
light is for 30 minutes, and automatically goes out after
30 minutes. If want a restart, have to connect again a
power supply after disconnecting power supply no less
than 8 seconds.
Suggest: to disconnect power supply after every time
use .
6. 安装
电缆室照明灯由光源控制单元、连接电缆和发光
头组成。光源控制单元配有接线端子可直接连接电
源，其 中 A1（+）接 AC“L”或 DC“+”，A2(-) 接 AC
“N”或DC“-”，+接连接电缆红线，-接连接电缆黑
线。光源控制单元安装在DIN 35mm标准导轨上，发光
头可用螺栓夹紧的方式安装在电缆室需要光照的地
方。
6. Installation
Cable cabinet lamp consist of light source control unit
and connecting cable and illuminance head.The light
source control unit has the wiring terminal that can
connect a power supply directly, among them, the A1
(+)connect the AC"L" or DC"+", the A2(-) connects the
AC"N" or DC"-",the + connect the red line of connecting
cable, the - connect the black line of connecting cable.
The control unit can mount at a standard DIN 35 mms
rail.The illuminance head can fix tightly in the suitable
place that the head illuminates a region in the demand
with screw .
外形尺寸图
Dimension diagram
光源控制单元外形尺寸
Light source control unit dimension
发光头外形尺寸
Illuminance head dimension
连接导线要求
Terminal Cross Section
10mm
导线截面积/Nominal Cross Section:2.5mm2
最大导线截面积/Max.Cross Section:4mm2
34.35
安装示意图
Mounting sketch map
|
放大图片
暂无相关下载
