YH-1*25天然胶护套电焊机电缆

型号 名称

Type name

YH 天然胶护套电焊机电缆

YH natural rubber sheath welder cable

YHF 氯丁或其它相当的合成胶弹性体护套电焊机电缆

YHF neoprene or other equivalent synthetic elastomer sheath electric welding cable

的使用要求：

Use requirements of YH electric welding machine cable:

(1)YH电缆是在低电压(zui高电压为200V)大电流的条件下工作,要求具有一定耐性。

(1) YH cable is working at low voltage (maximum voltage of 200V) under high current conditions, requiring a certain degree of tolerance.

(2)焊把线电缆长期允许工作温度不应超过65℃。

(2) long allowed working temperature of welding wire cable shall not exceed 65 DEG C.

(3)电机引接线电缆频繁地移动，扭绕和施放,要求柔软,弯曲性能好。

(3) motor wiring cables frequently move, twist around and cast, requiring soft, good bending performance.

(4)在施放中易受到尖锐钢铁构件的刮、擦,故要求电缆绝缘抗撕、耐磨等机械性能好。

(4) in the casting vulnerable to sharp steel components scraping, cleaning, so the cable insulation tear, wear and other mechanical properties are good.

(5)使用环境条件复杂,如日晒、水沸、接触泥水、机油、酸碱液体等,要求有一定的耐气候性和耐油、耐溶剂性。

(5) the use of complex environmental conditions, such as sun, water boil, contact mud water, oil, acid and alkali liquid, require a certain weather resistance and oil resistance, solvent resistance.

(6)有时会碰到热焊件,要求耐热变形性好。

(6) sometimes encountered hot weldment, requiring good thermal deformation.

(7)经常移动,要求外径小,重量轻。由于对此种电缆电性能要求不高,且使用环境条件复杂,在结构上要求满足各种复杂的环境因素是不适宜的。使用时注意改善使用条件,防止外来破坏。

(7) frequent movement requiring small external diameter and light weight. Because of the low demand for the electrical performance of the cable and the complicated use of the environment, it is not suitable to meet various complicated environmental factors in the structure. When used to improve the use of conditions to prevent foreign damage.

电焊机电缆[1]（YH电缆）全称高强度橡套电焊机电缆，俗称焊把线，是YC电缆（通用橡套电缆）的一种。用于电焊机二次侧接线及连接电焊钳、电焊机的专用电缆，其特性是电阻大、电压低。工作电压一般为450V到750V。

Electric welding machine cable [1] (YH cable) full of high strength rubber sleeve electric welding cable, commonly known as welding wire, is a YC cable (general rubber cable). For the electric welding machine two secondary side wiring and electrode holder, welding connection cable, its characteristic is high, low voltage resistance. Operating voltage is generally 450V to 750V.

电焊机电缆的结构为单线芯，一般为多跟铜丝组成铜丝组，多组铜丝组则组成电焊机电缆的导体部分，所以YH电缆线体较粗，铜丝数百根。多组铜丝的周围被一层耐热聚酯薄膜绝缘包裹。绝缘层一般为纯天然橡胶，铜丝为无氧铜，这样，才能保证线芯的良好导电性及电缆的安全性。

The structure of electric welding machine cable for a single core, usually with copper wire conductor composed of groups, groups of copper group is composed of welding cable, so YH cable body coarse copper wire, hundreds of root. Many groups around the copper wire by a layer of heat-resistant polyester film wrapped insulation. The insulating layer is pure natural rubber, copper wire for copper, so, in order to ensure the safety of wire and cable of good conductivity.